差壓變送器的注意事項

1.切勿用高于36V電壓加到變送器上，導致變送器損壞；2.切勿用硬物碰觸膜片，導致隔離膜片損壞；3.被測介質不允許結冰，否則將損傷傳感器元件隔離膜片，導致變送器損壞，必要時需對變送器進行溫度保護，以防結冰；4.在測量蒸汽或其他高溫介質時，其溫度不應超過變送器使用時的極限溫度，高于變送器使用的極限溫度必須使用散熱裝置；5.測量蒸汽或其他高溫介質時，應使用散熱管，使變送器和管道連在一起，并使用管道上的壓力傳至變壓器。當被測介質為水蒸氣時，散熱管中要注入適量的水，以防過熱蒸汽直接與變送器接觸，損壞傳感器；6.在壓力傳輸過程中，應注意以下幾點：a.變送器與散熱管連接處，切勿漏氣；b.開始使用前，如果閥門是關閉的，則使用時，應該非常小心、緩慢地打開閥門，以免被測介質直接沖擊傳感器膜片，從而損壞傳感器膜片；c.管路中必須保持暢通，管道中的沉積物會彈出，并損壞傳感器膜片。